-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
IPC-A-610: What's New With Rev F?
July 22, 2015 | Leo Lambert, EPTACEstimated reading time: 2 minutes
IPC generates many specifications related to printed circuit board fabrication, assembly processes and inspection criteria. The intent of the following article is to describe how the documents come about and how they are generated by providing an overview of the latest changes in IPC-A-610, Acceptability of Electronic Assemblies, hereafter identified as 610. Additionally, there are online courses available that will go through each one of these changes in details.
Background
Why are new revisions created? Can’t IPC just issue updates to the existing revision? Who defines what the changes are going to be and who approves of those changes? Why can’t they make changes for all the new technologies available? And the best question of all: Why does my product have some conditions that are not covered in the documents and specifications?
Taking just one document, 610, and trying to answer those questions will hopefully provide a window for customers, users, and manufacturers to see where these documents come from and how they are put together to upgrade the products being made, and hopefully improve the quality of those products.
Every five years, a new revision is created for all the specifications from IPC. This was mandated for all ANSI approved documents. Since many IPC documents were ANSI-approved, they had to be reviewed and updated on a regular basis, in our case five years. There are multitudes of implications with the release of new revisions. They include, but are not limited to: contract negotiations, purchasing of new specifications, and development of new certification training programs to cover the requirements of those documents for the trainers and the specialist. This is all accomplished by attending the semiannual meetings of IPC and participating in the task group meetings, where all the new information is presented, all the comments are reviewed to correct deficiencies in the existing revision, and all conflicting information is reviewed to verify that complementary documents are in agreement for criteria information.
Once all the information is reviewed and accepted by the committee, a draft is sent to the IPC community for review and comment. Once again there is a review and discussion on the comments, and subsequently another draft is created and the process repeats itself until all the comments are resolved and a new document is published.
Creating updates to the documents is also handled in the same fashion, and since the comments are considered critical, the review period is shorten to enhance the speed to which the approval cycle is made and then the documents are published for the user community. This is a relatively short process as it only addresses critical issues to the main body of the document.
So, what defines the changes? First, comments from the user community as found on the comment sheet in the back of every IPC specification. Second, submittal from the component manufacturers on new components being introduced for new technology applications. Finally, corrections needed from editorial and technical mishaps in the existing documents.
To read this entire article, which appeared in the June 2015 issue of The PCB Design Magazine, click here.
Suggested Items
PCBflow Helps Designers Choose Best Manufacturer for the Job
03/28/2024 | Andy Shaughnessy, Design007 MagazineI recently spoke with a few technologists who have first-hand experience with PCBflow: Susan Kayesar, technical product manager with Siemens; Evgeny Makhline, CTO of Nistec, a CEM based in Israel; and Peter Tranitz, senior director of technology solutions and leader of the IPC Design Initiative. They explain how PCBflow functions, from the designer’s and manufacturer’s viewpoint, and how this database helps break down the wall between these stakeholders.
ASMPT to Exhibit Smart Manufacturing at IPC APEX EXPO 2024
03/27/2024 | ASMPTWith its innovative, data-driven Intelligent Factory concept and a comprehensive hardware and software portfolio around SMT production, market and innovation leader ASMPT will be a major presence at the IPC APEX EXPO 2024, the industry’s main event in California.
Mycronic to Showcase More Versatile, High-productivity Assembly Solutions at IPC APEX EXPO 2024
03/27/2024 | MycronicMycronic, the leading Sweden-based electronics assembly solutions provider, will continue to respond to growing customer demand for high-flexibility, high-productivity solutions for zero-defect PCB assembly at IPC APEX EXPO 2024 in Anaheim, CA on April 9 - 11.
TRI Launches New Advanced Packaging 3D CT AXI Solution
03/26/2024 | TRITest Research, Inc. (TRI) proudly announces the launch of the SEMI 3D CT AXI solution, TR7600F3D SII Plus, marking a paradigm shift in precision and reliability for high-reliability electronics manufacturing, such as the Advanced Packaging Industry.
Blackfox Ready for IPC APEX EXPO 2024
03/26/2024 | Andy Shaughnessy, I-Connect007Blackfox Training Institute offers IPC-certified training for a myriad of PCB assembly techniques and standard certifications. With many technologists beginning to eye retirement, this training is at a premium. I recently spoke with Jamie Noland, director of training and education for Blackfox, about the company’s latest educational efforts, and his plans for the upcoming IPC APEX EXPO, where Blackfox will be exhibiting.