Albert Gaines: Design All Comes Down to Documentation
June 28, 2019 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 2 minutes
During SMTA Atlanta, I spoke with Albert Gaines of HiGain Design. We discussed Albert’s belief that everything starts with design and that too many engineers and designers focus solely on the final board at the expense of the documentation, which is a designer’s most important product. Do you consider your documentation to be a critical product?
Andy Shaughnessy: Albert, you are the founder, chief cook, and bottle-washer for HiGain Design. A minute ago, we were talking about how everything in electronics manufacturing really starts with design. You had an interesting point about some things that designers and design engineers sometimes neglect to consider early in the cycle.
Albert Gaines: I’ve been doing board layout since ’81, and I came through the drafting side of it. Documentation was our product. I think most engineers today lose the concept of the fact that the final product is not the prototype. They finally have it working, but they think they’re through. But their product is documentation—the Gerber package, ODB++ package, testability, assembly drawings, and all of the firmware. That documentation and traceability of that documentation is their product—not what’s sitting in the test lab.
Shaughnessy: How did we get to this point? I’m sure that there are people who have been doing this for 30 years and have never looked at the documentation as their final product.
Gaines: A lot has changed over the years because we’ve had a shift to where more EEs are doing more board layout, and we don’t have documentation departments in companies. Everybody is running freelance in their own cubicles. Nobody is enforcing what the documentation has to be. Ultimately, you end up with a board shop or an assembly house with a big void, wondering, “Am I going to get this data, the IPC-356 netlist, or the bare testing of the board? Or am I going to get an ODB++ for pick-and-place? What am I going to get? Do we have to recreate it after the fact?”
Shaughnessy: We always joke about how the designers get blamed for everything, but this sounds like one of the things that designers need to be aware of; it’s more about the documentation than anything else.
Gaines: Yes. It would be very good for each designer to have a checklist beside their desk when they’re getting ready to finish a product, detailing what they need to do—not just generate Gerbers and NC drill files and send it over the fence to a board shop. When I output documentation, I have folders for assembly data, bare board data, and testing data, and everything goes in each particular folder. If something’s for assembly, you grab the whole folder, which has anything that may deal with the assembly world or test world or bare board. It’s good to have that reminder. Another resource is your magazines. You’ve published information on what average documentation looks like, but I wonder how many designers look at that list and say, “What is that?” They don’t even know what it is.
To read this entire interview, which appeared in the June 2019 issue of Design007 Magazine, click here.
Suggested Items
Real Time with... IPC APEX EXPO 2024: Exploring IPC's PCB Design Courses with Kris Moyer
04/18/2024 | Real Time with...IPC APEX EXPOGuest Editor Kelly Dack and IPC instructor Kris Moyer discuss IPC's PCB design training and education offerings. They delve into course topics such as design fundamentals, mil/aero, rigid-flex, RF design, and advanced design concepts. They also highlight material selection for high-speed design, thermal management, and dissipation techniques. The interview wraps up with details about how to access these courses online.
Cadence Unveils Palladium Z3 and Protium X3 Systems
04/18/2024 | Cadence Design SystemsThe Palladium Z3 and Protium X3 systems offer increased capacity, and scale from job sizes of 16 million gates up to 48 billion gates, so the largest SoCs can be tested as a whole rather than just partial models, ensuring proper functionality and performance.
Signal Integrity Expert Donald Telian to Teach 'Signal Integrity, In Practice' Masterclass Globally
04/17/2024 | PRLOGDonald Telian and The EEcosystem announce the global tour of "Signal Integrity, In Practice," a groundbreaking LIVE masterclass designed to equip hardware engineers with essential skills for solving Signal Integrity (SI) challenges in today's fast-paced technological landscape.
On the Line With... Podcast Talks With Cadence Expert on Manufacturing
04/18/2024 | I-Connect007In “PCB 3.0: A New Design Methodology: Manufacturing” Patrick Davis returns to the podcast to talk about design rules. As design considerations become more and more complex, so, too, do the rulesets designers must abide by.
Designing Electronics for High Thermal Loads
04/16/2024 | Akber Roy, Rush PCB Inc.Developing proactive thermal management strategies is important in the early stages of the PCB design cycle to minimize costly redesign iterations. Here, I delve into key aspects of electronic design that hold particular relevance for managing heat in electronic systems. Each of these considerations plays a pivotal role in enhancing the reliability and performance of the overall system.