Making the Most of PCB Materials for 5G Microwave and mmWave Amps


Reading time ( words)

Millions of cell phones trying to connect voices and download unimaginable numbers of files worldwide point to the inevitability of fifth generation (5G) wireless communications networks. 5G is coming, and it will require the right circuit materials for many different types of high-frequency circuits, including power amplifiers (PAs). 5G represents the latest and greatest in wireless technology, and it will be challenging to design and fabricate, starting with the circuit board materials, because it will operate across many different frequencies, such as 6 GHz and below, as well as at millimeter-wave frequencies (typically 30 GHz and above). It will also combine network access from terrestrial base stations and orbiting satellites. But by careful consideration of mechanical and electrical requirements, high-frequency circuit materials can be specified that enable the design and development of 5G PAs no matter the frequency.

Ideally, a single circuit material would be a suitable starting point for PAs at all frequencies. However, amplifiers at different frequencies have different design requirements and are best supported by circuit materials with different characteristics best suited to the different frequencies. For example, insertion loss or dissipation factor can be more or less depending on the type of circuit material. Every circuit material will suffer some amount of loss, which typically increases with increasing frequency. The loss performance of a given circuit material may be acceptable within the microwave frequencies to be used in 5G networks but not within the millimeter-wave frequency range, where signal power tends to be less with increasing frequencies. The circuit material that provides the low loss needed for high PA gain and output power at microwave frequencies may not be the best choice of material for a PA at millimeter-wave frequencies.

The design requirements for a key circuit material parameter, dielectric constant (Dk), are much different for microwave frequencies, such as the 6 GHz and below used with 5G systems, than for millimeter-wave frequencies, such as 30 GHz and above, as will be used for short-range backhaul links in 5G wireless networks. Selecting an optimum circuit material for each band of frequencies requires understanding which Dk value best supports each of the two different frequency ranges. Then it is a matter of finding circuit materials that possess those Dk values along with as many as possible of the other circuit material attributes that help make a good, high-performance, high-frequency PA.

To read this entire article, which appeared in the May 2018 issue of Design007 Magazine, click here.

Share

Print


Suggested Items

January 2019 Issue of Design007 Magazine Available Now

01/15/2019 | I-Connect007
The component shortage is getting crazy. Some PCB designers are finding their favorite capacitors on 50-week and 80-week lead times, or worse. How do you design a board today when the components you need won’t be available for a year or more? In the January 2019 issue of Design007 Magazine, we asked our expert contributors to explain the current component shortage, as well as some of the workarounds that can help you get your next design out the door sooner rather than later.

A Fractal Conversation with Jim Howard and Greg Lucas

01/15/2019 | Barry Matties and Andy Shaughnessy, I-Connect007
Veteran PCB technologists Jim Howard and Greg Lucas have made an interesting discovery: Certain shapes of copper planes make a PCB run more efficiently than other shapes, a process they dubbed fractal design. It doesn’t appear to cost a penny more, and testing suggests that fractal design techniques could eliminate edge noise. Barry Matties and Andy Shaughnessy asked Jim and Greg to discuss the fractal design process, and the advantages of using this technique.

Rainer Beerhalter Discusses His AltiumLive Munich Presentation

01/11/2019 | Andy Shaughnessy, Design007 Magazine
Rainer Beerhalter is a physicist, and according to his design bureau’s website, “founder, owner, and mastermind” of B GMBH. Rainer attended the first AltiumLive in Munich in 2017, and he’s returning to this year’s event in Munich January 15–17. I asked him to tell us about the class he’ll be teaching in Munich, and why he decided to come back for the sophomore AltiumLive show.



Copyright © 2019 I-Connect007. All rights reserved.